Gmc-i Messtechnik Port Devices Driver Download For Windows 10

1. Gmc-i Messtechnik Port Devices Driver Download For Windows 10 64-bit
2. Gmc-i Messtechnik Port Devices Driver Download For Windows 10 Windows 7
3. Gmc-i Messtechnik Port Devices Driver Download For Windows 10 Pro

3 Installing the USB Device Drivers The USB device drivers have to be installed in order to operate test instruments or a memory adapter (with USB port) at a PC. Suitable IrDa-USB adapters must be used for devices with RS 232 port. GMC-I Driver Control software for installing the USB device drivers can be downloaded from our website. GMC-I Messtechnik GmbH 3 1 Ribbon cable with RS232 plug for connection of the SI module to the tester 2 USB socket connector for the transmission of stored data to the PC 3 LED signal lights up green when USB interface is active provided the USB device driver has been installed to the connected PC.

(Cable should NOT be connected to your laptop yet. Only connect it when instructions say so.)

Windows XP, Vista, 7:

Bought ELM327 from Total Car Diagnostics?

• Install DRIVER PACK 3.

Didn't buy ELM327 from Total Car Diagnostics?

Install all 4 driver packs below. Reason why so many to install is various ELM327's use different hardware chips. So one pack below should work.

—

If you bought ELM327 cable from elsewhere (clones, eBay, other manufacturers) then install all Driver Packs below, because they cover widest range of chip makers..

• DRIVER PACK 1
  Steps to install Driver Pack 1:
  
  • If you have 64-bit Windows, double-click on: CP210xVCPInstaller_x64
  • If you have 32-bit Windows, double-click on: CP210xVCPInstaller_x86
    

That's it!

Go to Step 2 below to test if everything is working ok..

Windows 8, 10:

Important: Any ZIP file below must be extracted specifically to Desktop. Then run the .exe file as Administrator. (Right-click > Run as Administrator)

Bought ELM327 from Total Car Diagnostics?

• Install DRIVER PACK 3.

Didn't buy ELM327 from Total Car Diagnostics?

Install all 5 driver packs below. Reason why so many to install is various ELM327's use different hardware chips. So one pack below should work.

• DRIVER PACK 1
  Steps to install Driver Pack 1:
  
  • If you have 64-bit Windows, double-click on: CP210xVCPInstaller_x64
  • If you have 32-bit Windows, double-click on: CP210xVCPInstaller_x86
    
• DRIVER PACK 4
  
• DRIVER PACK 5 ^{Most Important!}
  Steps to install Driver Pack 5:
  
  1. Please FIRST move the unextracted folder to your Desktop, else below #2 step won't show 'Install' option.
     
  2. Right-click on 'ser2pl' (icon has a little gear pic in it) and choose 'Install', as per below pic:
     
  3. Connect ELM327 cable to your laptop. Then..
     Go to: Control Panel » System » Device Manager » Ports (COM & LPT)
     You will likely see a yellow mark next to 'Prolific', like this:
     Right-click on it » Update Driver Software
     
  4. Click 'Browse my computer for driver software'.
     
  5. Select 'Let me pick from a list of device drivers on my computer'.
     
  6. UNcheck 'Show compatible hardware'.
     
  7. Select: Prolific driver version 3.3.2.102
     
  8. Install. That's it! The yellow triangle next to 'Prolific..' should be gone.

That's it!

Go to Step 2 below to test if everything is working ok..

(You can now CONNECT your ELM327 USB cable to any port on the laptop.)

Ok, we're almost ready to start scanning your vehicle.

First, let's ensure that everything is working fine!

Here's how..

Windows Vista/7/8/10: Control Panel » System » Device Manager

Windows XP: Control Panel » System » 'Hardware' tab » Device Manager

Notice any device with any one of the following names:

1. FT232R USB UART
2. Prolific USB-to-Serial..
3. USB Serial Port
4. USB2.0-Serial
5. Silicon Labs CP210x USB to UART Bridge

NONE of above devices should have a yellow mark () next to them.

If none of the above has a yellow mark, then congratulations! You're ready to begin scanning your car(s). Click here on how to connect to your car in the next 5 minutes..

Drivers diamond scsi & raid devices. If any one of above devices has a yellow mark, then:

1. Right-click on that device » Uninstall
2. Unplug cable
3. Restart PC
4. Download and unextract DRIVER PACK 6
5. Double-click on 'InstallUSB' to install
6. Connect cable to laptop. Yellow mark should now be gone. Success!
   If yellow mark is STILL not gone after doing 1-6 above, then do this:
   

   a) While cable is plugged in, right-click on device with the yellow mark.
   b) Click on: Update Driver Software
   c) Choose: Browser my computer for driver software
   d) Browse to and select folder where you unextracted Driver Pack 6. Make sure 'Include subfolders' is ticked ON.
   e) Click on: Next
   f) If you get RED warning, choose: Install this driver software anyway
   g) After it installs successfully, another yellow mark may appear under 'Other Device'. Eg:
   h) If g above is true, then do steps a-f for 'Unknown Device'. It may also show as 'COMx'.

Even DRIVER PACK 6 didn't help? Then likely it's a 'Code 10 error' next to 'Prolific USB-to-Serial' device. Click here to fix that.

Even 'Code 10 error' fix didn't help and yellow mark () is STILL not gone? Go to Troubleshooting below.

Step 1: Install your OBD2 software (if you don't have it — checkout TOAD OBD software). Do NOT launch it yet.

Step 2: Connect ELM327 USB to your computer and car's OBD port (usually underneat dashboard/steering wheel).

Step 3: Place the key in the ignition and turn it forward to 'ON' position. (Position where all dashboard lights are on. This is one position before engine starts.)

Step 4: Start your OBD diagnostic software. Click 'Connect', and it should auto-connect to your vehicle. That's it!

TIP: If you want maximum data reported from the car — turn on the engine.

Yes, you can safely drive the vehicle while ELM327 is plugged in and application is monitoring car's data. Keep eyes on the road at all times.

Common Solutions:

If you're unable to connect successfully to your car, then that's because of 2 reasons:

1. Your vehicle is notOBD2 compatible.
   
2. Random issues that can be fixed with below solutions..

Here are solutions in recommended order:

1. First check that ELM327 is physically working (not defunct). When you plug in the cable into a USB port, all the lights on ELM327 interface/device should flash. And then it'll return to 1 red light (power).
   Condition of a defunct ELM327 interface: All lights will not initially flash, and only red light will be on.
   
2. Restart computer (while keeping cable connected to laptop). Try again.
   
3. Plug USB into different physical port of your computer. Try again.
   
4. If all above solutions fail, then we will help you (only if you are Total Car Diagnostics customer). Here's all you need to do..
   

   Connect ELM327 USB cable into laptop. (Don't need to plug the other end to car)

   Step 1: Go to Control Panel.

   Windows Vista/7/8/10: Control Panel » System » Device Manager
   Windows XP: Control Panel » System » 'Hardware' tab » Device Manager

   Step 2: Expand 'Ports (COM & LPT)' and 'Other Devices'.

   Step 3: Take picture of the screen (Press 'Print Screen' key on the keyboard then paste into any graphics program. Or take shot with camera/phone.)

   Step 4:Contact us and attach the picture.

Free Software To Test If ELM327 is Working with Windows and Vehicle..

Step 1: Install EasyOBD. Do not launch it until Step 4 below.

Step 2: Connect ELM327 USB/Bluetooth to laptop and car.

Step 3: Turn on car ignition. (One step before engine turns on)

Step 4: Launch EasyOBD. It will automatically connect.

If first 5 lines are GREEN — then ELM327/Windows is 100% installed correctly. In this case, can get TOAD pro software.

If any of the first 5 lines are RED — then OBD2 scanner won't work on your car. Rather take it to mechanic.

• ELM327 AT Commands: List of commands you can manually type into OBD software terminal.

Here I’m only speaking for the Tech2win software to use with VXDIAG VCX NANO for GM. Website says that Tech2Win only runs from a Windows XP/7 32-bit computer. But I have laptops running Windows XP, 7, 8, and 10 32 & 64 bit. So i could try on any operating system.

That i did run straight from a Windows 10 64-bit laptop.

Gmc-i Messtechnik Port Devices Driver Download For Windows 10 64-bit

Tech2Win Windows 10 64 bit: need luck!

On a Windows 10 64-bit laptop – I’ve seen lots of bad experience on forums.

But the tech2win software runs just fine on my Windows 10 64bit laptop. Would be even cooler with a surface pro or similar tablet.

Went into my device manager, expanded the Human Interface Devices and disabled the touchscreen device. I then could run Tech2Win and the MDI selector popped up like it should. If your device only has a touchscreen you will have to add a keyboard (either wired or Bluetooth) before you disable the touchscreen so you can use Tech2Win.

Gmc-i Messtechnik Port Devices Driver Download For Windows 10 Windows 7

I’m willing to bet some device that some GM dealerships run the software on are touchscreen (with a compatible Lib) and in windows 10 we have some sort of touchscreen Lib (not compatible) conflict with the application.

Tech2Win Windows 10 with Windows 7 mode: worked!

On tech2win, although the op is stating that its working in 64 bit mode, really want to go through it to double check if it needs to run in win 7 compatible mode for everything to work “correctly” instead.

Putting tech2 win into win 7 compatibility mode is not hard to do.

Go to the start icon for tech2win, right click it and go to properties, and see if you can click the box and make it run it in win 7 mod.

If the box is grayed out and you can not do it this way, click on the Windows icon, type in run in the search box, then find run program made for a previous version of windows in list it will bring out and click on that to open that program. From here, it pretty straight forward to find Tech2 win, and change tech2 win so it running in win 7 compatible mode.

Gmc-i Messtechnik Port Devices Driver Download For Windows 10 Pro

Another good tip: Tech2Win Windows 7 32/64 bit – also worked
On a 32bit machine running win 7, tech2 seems to be working since I just did a quick check on the car with it, But still trying to skin the cat to get the VXDIAG VCX Nano to work on my 64bit machine.

Here is the tutorial for reference.

Source: http://blog.obdii365.com/2015/12/24/install-vxdiag-vcx-nano-for-gm-tech2win-11-27/

Ps. The method also can be used for 64bit Windows 7.